Why is My Pur Water Filter Blinking Red After Filter Change?

If you are using a PUR water filter, you might be wondering why it is still blinking red after a filter change. The following will give you a brief overview of what you should do when this happens.

MKII Water Filter

Introduction

There are a few reasons why your PUR water filter may be blinking red. In most cases, the light isn't the cause of the problem, but it is a sign that your filter needs to be replaced.

A PUR water filter is an advanced device that filters out many of the contaminants that can be found in tap water. This will ensure that you get clean, refreshing drinking water. It also helps you save money over purchasing bottled water.

Your PUR water filter should be able to provide you with a good two months' worth of pure, fresh water before it becomes necessary to change the filter. However, you'll want to make sure that you replace the filter before it wears out.

If the green light is blinking, it's a signal that your filter is working properly. The filter will be able to remove a lot of the contaminants, like chlorine and odor, from your drinking water.

Another reason your filter may be blinking red is if there are dirt particles trapped on the filter itself. Although this isn't the main reason, it's important to clean the filter to ensure it's performing at its best.

Different Lights: Green and Red

When you turn on your PUR water filter, you may notice that the indicator light has a green or red light. If it is the green light, then it means that the water is safe to drink. However, if it is the red light, then you should immediately replace the filter.

Water filter indicators are a smart way to monitor the condition of your filter. They have been developed with advanced technology to be hard to miss. The green and red lights will notify you when to change the filter. This will help you stay on top of the replacement schedule.

You can find a replacement for your PUR water filter at a local store. You can also buy a multi-pack to save money in the long run.

Before you can replace the filter, you need to reset the system. To do this, simply press the reset button on your unit for three to five seconds. Once it has been reset, the filter should work as normal.

If you are experiencing issues with your PUR water filter, you should first check the system's water pressure. Low water pressure could cause the light to blink. Turning off the faucets or shower heads can also be helpful.

Water Filter Life

When you replace a Pur water filter, it will sometimes flash a red light. This is not a big concern. It is just a normal part of the process.

PUR filters work a little differently than other filters. They have an indicator that shows a green light when the filter is functioning properly. A yellow or red light indicates that the filter needs to be replaced.

To fix the problem, you need to remove the cover of the water filter. Then, you need to hold the reset button for five seconds. After a few seconds, the cover should go back on. You can also rinse the filter with running water.

If your PUR faucet filter is blinking red, it may be because the electric circuit is faulty. In this case, you will need to contact a technician. Alternatively, you can take your device to a local PUR store outlet and have them change the electric circuit for you.

You can also reset the PUR filter yourself. It requires a small button. Simply press it for a few seconds and then pull it out of the housing.

Electrical circuit of the filter

If your PUR water filter light is blinking red after filter change, there are a few things you can do to fix it. The first step is to check your water pressure. Make sure the faucet is turned off and that all the taps are off.

You can also check to see if the base of your filter is connected properly to the faucet. This is important because a leak could cause flooding in your home. It is also possible that your filter has holes.

You can clean the filter with mild soap and water. If that doesn't work, try putting the filter under running water for five minutes. Once the new filter is installed, reset the filter light.

If the indicator lights are still not working, you can go to a nearby PUR store. They sell replacement electric circuits. Alternatively, you can call PUR customer support to ask if they have any troubleshooting tips for your model.

Another option is to simply replace the filter. This will ensure that your filter continues to work well.

The Reset Button On A PUR Water Filter

If you have recently changed the filter in your PUR water filter, you may notice that the Reset button starts blinking red. This is normal. Although this doesn't mean that anything is wrong with your filter, it is important to reset it.

Depending on the size of your PUR water filter, you can expect the Reset button to blink in various colors. For example, the light indicator can be yellow, green, or red.

When the light is blinking green, the filter is in good condition and should work as usual. However, if it is blinking red, it indicates that the filter needs to be replaced. There are some possible reasons for this, including leaks. It is best to call a technician from PUR to diagnose and repair the problem.

The Reset button on a Pur water filter is located on the pitcher or faucet filter. Pressing the button for three to five seconds will reset the system. Once the reset is done, replace the old filter with a new one. After a few days, you should see that the filter works again.

Why Is My PUR Faucet Filter Still Blinking Red?

A PUR faucet filter is supposed to last for at least 100 gallons of water before it stops working. However, if your filter still blinks red after the filter is replaced, there may be some problems. The most common issue is a clogged filter.

If this happens, it is time to replace the filter. If you don't have a replacement, you can call PUR customer care to help you troubleshoot the problem. Before replacing the filter, you may want to clean it with a soft cloth. This will remove any accumulated debris and sediment that may be causing the light to blink. Afterwards, you can run the system without water to reset the filter.

If this doesn't work, you may need to replace the whole filtration system. You can do this by going to a local PUR store outlet. They'll be able to replace the electric circuits for you. Another common problem is mishandling the filter. Mishandling can cause leaks during the shipping process or during the filter change. It can also cause the filter to not perform as well. Read more.

Conclusion

When you notice your pur water filter blinks red after filter change, the first thing you need to do is find the cause. A filter that is clogged with dirt, debris, and minerals cannot properly filter your water. It can also affect the taste of your water. If this is the case, you should consider replacing the entire filtration system.

This is a common problem. Many times, it is the result of mishandling the unit. Leaks can occur during shipping or during a filter replacement.

If you are unsure whether your PUR filter needs to be replaced, you can ask a PUR technician. These technicians can determine the cause and provide you with recommendations for an effective solution. The easiest way to ensure your filter is not clogged is to replace it.

You can also use the indicator light on the PUR water filter to indicate when the filter needs to be replaced. While the light does not have a set expiration date, it is usually good for about two months.

Depending on how much you use your PUR filter, you may need to change the battery periodically. Batteries tend to last quite long, though.